I downloaded the trial version of OrCad Pspice. I'm trying to do some simulation using Capture with opamp and transistor but it doesn't work. The error message is:ERROR(ORPSIM-15108): Subcircuit UA798 used by X_U1A is undefined. How can I solve the problem?
I also need LT3080 and LT3081 for simulation. Are they available?
Copyright © 2020 Cadence Design Systems, Inc. All rights reserved.
Hi,
It is strange that the simulation does not work, because the component UA798 is included in the default PSpice component. Could you tell me please which version you installed? If you open the simulation profile, which libraries do you have included in Configuration files --> Libraries?
In relation to the components LT3080 and LT3081, they are not avaiable for simulation in the default libraries. So you have to look for them in internet.
regards
I'm getting the same error, but with component LM741.
Version is 17.4-2020-S004; configured libraries are nom.lib*, nom_pspti.lib*, lm741.olb, and lm741.lib
Thanks, I've found a solution to the problem. Can you please give me some advice on where I can found LT3080 or LT3081 for simulation??
Hi,
help me, please, solve a problem.
I did with Create Subcircut Format Netlist PSpice modell for Transformer
.SUBCKT Transfformer2W Pri1 Pri2 Sec1 Sec2
R_Rp1 PRI1 N01732 500 TC=0,0
L_Lp1 N01732 PRI2 100mH
R_Rs1 N01742 SEC1 10 TC=0,0
Kn_K1 L_Lp1 L_Ls1 1
L_Ls1 N01742 SEC2 100mH
.ENDS
I did the Library *.olb with Model Editor
STATUS: PSpice Schematics to Capture translator (17.2.0.d001)
STATUS:
STATUS: Translator started at Monday, June 18, 2018 09:14:14
STATUS: c:\cadence\spb_17.2\tools\bin\sch2cap -f "C:\Users\abramov\Documents\Personalordner\OrCad Projekts\Transformer2W\Transfformer2W-PSpiceFiles\Transfformer2W\Transfformer2W.LIB" -o "C:\Users\abramov\Documents\Personalordner\OrCad Projekts\Transformer2W\Transfformer2W-PSpiceFiles\Transfformer2W\Transfformer2W.olb" -i C:\SPB_DATA\cdssetup\OrCAD_PSpice/17.2.0/PSpice.ini
INFO(ORSCH-1029): Using existing library 'c:\cadence\spb_17.2\tools\Capture\Library\PSpice\modeled.etc'.
INFO(ORSCH-1031): Created new library 'C:\Users\abramov\Documents\Personalordner\OrCad Projekts\Transformer2W\Transfformer2W-PSpiceFiles\Transfformer2W\Transfformer2W.olb'.
STATUS: Translator stopped at Monday, June 18, 2018 09:14:15
STATUS: 0 Error messages, 0 Warning messages
During the test run of simulation of the circuit with a load resistor, an error occurs:
* Profile Libraries :
* Local Libraries :
* From [PSPICE NETLIST] section of C:\SPB_DATA\cdssetup\OrCAD_PSpice\17.2.0\PSpice.ini file:
.lib "nom.lib"
.TRAN 0 18m 0 50u
.OPTIONS ADVCONV
.PROBE64 V(alias(*)) I(alias(*)) W(alias(*)) D(alias(*)) NOISE(alias(*))
.INC "..\SCHEMATIC1.net"
* source TR2W_S
X_U1 N00176 0 N00195 0 TRANSFFORMER2W
R_R1 N00195 0 1000k
V_V1 N00176 0
+SIN 0 50 10k 0 0 0
.END
You need to add the LIB file for you sub-circuit to the Simulation Profile, PSpice>Edit Simulation Profile, Configuration Files, Library, use the upper Browse button to locate your LIB file and use the Add to Design button to add your LIB file to the Design Simulation Profile.
This method did not fix the issue on my end: I get
ERROR(ORPSRVR-2151): Cannot add the file as it is already configured!.
Thank you very much for your help!
Everything works perfectly.
Is it possible to make so, that the modells by me could be connected at a stage of creation of the circuit throuth a standart command „to add base“ (Naturally, I will create a OLB library for this model and associate it with the corresponding PSpice model)?
The error message "ERROR(ORPSIM-15108): Subcircuit UA798 used by X_U1A is undefined" shows Pokemon Showdown that PSpice cannot find the subcircuit named UA798, which is used by circuit component X_U1A.
We offer both kind of Pune escorts service - IN CALLS and OUT CALLS. Our agency will take care if you are looking for Pune Call Girls in costly hotels. On the other way if you do not have any hotel then you can come to our agency hotel at any time 24x7.
Particular interviews furnish firsthand message on mart size, industry trends, ontogeny trends, capitalist landscape and outlook, etc. Freizeitjacke für Damen
If you do not find a library for "UA798," you may need to download or create a corresponding emulation library. This may require you to search for documentation
The Password Game or mockup information from an official source, or create a custom mockup library for that asset.
The LIB file for your sub-circuit must be added to the Simulation Profile. Go to PSpice>Edit Simulation Profile, Configuration Files, Library, find your LIB file using the top Browse button, then select Add to Design to add it to the
tunnel rush Design Simulation Profile.
Hi, I am using Orcad 16.6-p005(v16-6-112D) , on Windows 10 and any model like Max907 from Pspice/MAX.OLB or IRF152 from powermos.olb retro bowl college